Showingof 347 item(s)
a specialized check valve for Arctic Spas hot tubs, specifically for models with the Progressive Filtration system and high-efficiency pumps. It is designed to prevent water from flowing backward into the ozonator, which can cause damage to the electronic
$--.--
It is typically found on models from 2020 and later, specifically in the Custom Series. The valve is a hydraulic component that allows for the isolation or servicing of the filter without needing to shut down the entire system.
$--.--
2019-Current
Swim Spas & Summit XL Models only (Pre & Post 2020)
Can replace PAK-112150 Spas Built in 2019 or earlier
monitors water pressure in the heater manifold and protects the heater from damage if there is insufficient water flow.
Swim Spas & Summit XL Models only (Pre & Post 2020)
Can replace PAK-112150 Spas Built in 2019 or earlier
monitors water pressure in the heater manifold and protects the heater from damage if there is insufficient water flow.
$--.--
Used as a shut-off valve to isolate different sections of the hot tub's plumbing. This allows for maintenance or repair of components like pumps or heaters without fully draining the tub.
$--.--
Fits the AquaFlo Flo-Master XP and XP2 pump series.
Designed for pumps rated at 4.0 horsepower.
Used on motors with either a 48 or 56 frame.
The pump seal assembly is sold separately and should also be replaced when replacing the impeller to prevent le
Designed for pumps rated at 4.0 horsepower.
Used on motors with either a 48 or 56 frame.
The pump seal assembly is sold separately and should also be replaced when replacing the impeller to prevent le
$--.--
This impeller is for pumps with an AquaFlo/Gecko Flo-Master XP2e wet end.
It is rated for a 3.0 horsepower (HP) motor.
It is rated for a 3.0 horsepower (HP) motor.
$--.--
connects the pressure switch to the main control board (PC board). A faulty pressure switch cable can prevent the heater from operating correctly and may cause flow-related error messages on the topside control panel.
$--.--
This vacuum draws ozone (or the sanitizer produced by the Onzen system) into the injector and mixes it efficiently into the water stream before it re-enters the spa.
$--.--
has one male and three female connectors and is used to power multiple LED light fixtures within the hot tub.
$--.--
This wire connects the backlit cupholders to the main lighting system, allowing the cupholders to be illuminated in sync with the other spa lights.
$--.--
designed to prevent water from leaking past the impeller shaft into the pump's motor, and replacement is recommended when you notice leaks around the pump shaft or when replacing a worn or damaged impeller.
$--.--
2010-2019
a complete assembly that includes the large, black and clear bearclaw handle and the clear threaded cap. This valve is used to redirect the flow of water to different jet zones in the spa.
a complete assembly that includes the large, black and clear bearclaw handle and the clear threaded cap. This valve is used to redirect the flow of water to different jet zones in the spa.
$--.--
a round, two-tone headrest used in select Arctic Spas models, primarily those manufactured between 2006 and 2008. The pillow attaches to the hot tub shell with a single, centered suction cup on the back.
$--.--
a component used in 2020 and newer Custom Models that are equipped with the Progressive Filtration System. It is responsible for detecting the RFID chips embedded in proprietary Progressive Filters.
$--.--
As the "master" controller, it is the main board that manages the light effects for the spa's interior lights. It uses a telephone-style 4-pin plug and a 2-pin 12V output for the lights.
$--.--
The ultrasonic disc vibrates at a high frequency to break water into a fine, ethereal mist that cascades over the spa's surface.
$--.--
holds the internal components of the fogger, such as the ultrasonic disc, and fits into the spa shell.
$--.--
a replacement housing for the electrode cartridge in Arctic Spas' saltwater system, specifically for models with the SpaBoy water management system. This housing is grey and includes the "niche" area for mounting into the spa's plumbing.
$--.--
provides the necessary power to the Onzen generator, which sanitizes the water through electrolysis.
$--.--
This probe works by sending temperature readings to the spa's control pack, allowing it to turn the heater on and off to maintain the water at the set temperature.
$--.--
2005-2019 Coyote Models
Designed for Coyote hot tubs that use the Gecko Global Eco Pak control system.
Designed for Coyote hot tubs that use the Gecko Global Eco Pak control system.
$--.--
a specific Gecko TSC-80 topside control panel interface board used in Arctic Spas hot tubs manufactured between 2007 and 2019. This part is the internal component that connects the control pad's buttons to the main circuit board.
$--.--
a "slave" light, meaning it connects to and is controlled by a "master" LED light. The "L4" designation indicates that the light strip is 4 LEDs long.
$--.--
a consumable electrode cartridge for the Onzen saltwater sanitization system. Designed for the Onzen system, not the newer SpaBoy system, which uses a different cell. The cartridge should be replaced annually to ensure proper sanitizer production.
$--.--