Showingof 34 item(s)
replacement o-ring for the 1 1/2-inch pump unions used on the circulation pumps. The "(225)" indicates a specific size used for sealing the pump's union to the spa's plumbing to prevent leaks.
$--.--
1996-1998
Arctic/Coyote Models
a replacement gasket for the wet ends of pumps used in Arctic Spas hot tubs. It creates a watertight seal between the wet end and the pump's motor.
Arctic/Coyote Models
a replacement gasket for the wet ends of pumps used in Arctic Spas hot tubs. It creates a watertight seal between the wet end and the pump's motor.
$--.--
The o-ring creates a watertight seal for the large, 4-inch union on the high-flow Speck pump used for the Niagra water feature.
$--.--
is a component used to vent trapped air from the pump's wet end. It has a 3/8" barbed end for connecting to a hose and a 1/4" MPT (male pipe thread) end for screwing into the pump housing.
$--.--
2003-2007
Arctic Models
This is the replacement circulation pump specifically for spas with the Peak Ozone II system.
Arctic Models
This is the replacement circulation pump specifically for spas with the Peak Ozone II system.
$--.--
designed to create a watertight seal between the pump and the plumbing, preventing leaks. The "(229)" refer to the o-ring's internal dimensions, ensuring a precise fit.
$--.--
a high-flow, complete suction fitting assembly. It is designed to allow a large volume of water to be drawn by the hot tub pump.
$--.--
The fitting is rated for a flow rate of up to 250 gallons per minute (gpm), suitable for powerful pumps. Can be replaced with JET-110594
$--.--
The fitting is rated for a flow rate of up to 250 gallons per minute (gpm), suitable for powerful pumps.
$--.--
This impeller is for pumps with a 1 HP, 1-speed North American Pentair motor used in specific Arctic Spas and Coyote hot tub models.
$--.--
Fits the AquaFlo Flo-Master XP and XP2 pump series.
Designed for pumps rated at 4.0 horsepower.
Used on motors with either a 48 or 56 frame.
The pump seal assembly is sold separately and should also be replaced when replacing the impeller to prevent le
Designed for pumps rated at 4.0 horsepower.
Used on motors with either a 48 or 56 frame.
The pump seal assembly is sold separately and should also be replaced when replacing the impeller to prevent le
$--.--
This impeller is for pumps with an AquaFlo/Gecko Flo-Master XP2e wet end.
It is rated for a 3.0 horsepower (HP) motor.
It is rated for a 3.0 horsepower (HP) motor.
$--.--
This specific part is designed for the Flo-Master XP2e series of pumps and has a 2-inch threaded intake and discharge. It is intended for use with a 4.0 horsepower, 56-frame, thru-bolt motor and is suitable for either a single-speed or two-speed motor.
$--.--
used with a 1-speed, 2.5 horsepower, 48-frame motor. The plumbing connections are 2-inch buttress threads (which measure approximately 3.1 inches outside to outside).
$--.--
operates on standard 110V household outlets. This pump provides both a high speed for massaging jets and a low speed for energy-efficient filtration.
$--.--
This high-performance pump provides both a low-speed setting for energy-efficient filtration and a high-speed setting for powerful hydrotherapy jets. A 3.0 horsepower, 240V pump with 2-inch connections.
$--.--
this is the wet end of an Aquaflo XP2E pump used in some models from 2011 onward, including those with Epic pumps rated 2 through 5 horsepower. The wet end is the part of the pump that comes into contact with the water and contains the impeller.
$--.--
used to securely install and support the pump motor, helping to reduce vibration and extend the pump's lifespan
$--.--
2001-2006
Arctic/Coyote Models
used to securely mount the circulation pump within the hot tub's equipment bay, helping to reduce vibration and ensure the pump operates efficiently.
Arctic/Coyote Models
used to securely mount the circulation pump within the hot tub's equipment bay, helping to reduce vibration and ensure the pump operates efficiently.
$--.--
This union connects the main 2 1/2-inch intake plumbing to the pump.
$--.--
This union connects the 2-inch buttress-threaded discharge fitting on a Waterway pump to the spa's 2-inch slip (socket) plumbing.
$--.--
This component is a complete assembly that includes the nut, a 90-degree sweep tailpiece, and the o-ring. It connects the pump's 2-inch threaded buttress fitting to the spa's 2-inch slip (socket) plumbing.
$--.--